Virtual KMON
~~~~~~~~~~~
The Virtual KMON (VKMON) is a program that allows you to coinfigure an RT-11
system image file.

VKMON commands are a subset of Keyboard Monitor (KMON) commands.
VKMON commands differ from KMON commands that they are directed to the
monitor file rather than to the current running system.

VKMON supports RT-11 V4.0 and newer versions except for a memory-resident
RT-11 (MRRT).
A monitor MAP file is required to use VKMON.

Invoking VKMON
~~~~~~~~~~~~~
You can invoke VKMON in different ways.
You need to specify a system image file and corresponding MAP file.

Default device name for both monitor and MAP files is SY:.
Default file type for monitor file is .SYS.
Default file type for map file is .MAP.
Bu default MAP file name is the same as a monitor file name.

R/RUN command:
	.R VKMON
	*[ddn:]file[.SYS][,[ddn:][file[.MAP]]]

CCL command (RT-11 V5.0 and newer):
	.VKMON [ddn:]file[.SYS][,[ddn:][file[.MAP]]]

Examples:
	.R VKMON
	*RT11SJ			!SY:RT11SJ.SYS and SY:RT11SJ.MAP

	.VKMON RT11SJ,RTSJ	!SY:RT11SJ.SYS and SY:RTSJ.MAP

	.VKMON RAFSJ,DK:	!SY:RAFSJ.SYS and DK:RAFSJ.MAP

VKMON commands
~~~~~~~~~~~~~~
After specifiing of monitor and MAP files VKMON enters command mode.
You can exit command mode by pressing CTRL/C or by EXIT command.
If you're using a command file to run VKMON, you should use EXIT command.
Using of ^C in a command file where VKMON is in command mode suspends
execution of the command file, and allows you to enter VKMON commands from
terminal.

There are some differences between KMON and VKMON commands:
- RESET command in VKMON resets all changes not saved via SAVE command.
- SHOW TERMINALS in VKMON allows you to show terminal settings in a
  singleterminal system.
- SET TT in VKMON allows you to apply settings to any terminal line of a
  multiterminal system.

The following speeds are sllowed in SET TT SPEED command for DZ/DH lines:
50, 75, 110, 134 (for 134.5), 150, 300, 600, 1200, 1800, 2000, 2400,
3600 (DZ only), 4800, 7200, 9600, 19200 (DH only), 38400 (DH only).

The following commands are supported in VKMON:

.DA[TE] [dd-mmm-yy[yy]]
	- Show/set system date.
	  Please note: setting a date in a monitor file may affect programs
	  used to set date/time from the system startup file.

.DA[TE] NUL[L]
	- Clear system date.

.EX[IT]
	- Exit command mode.

.INS[TALL] dd[:]
	- Install device handler.

.PA[TCH]
	- Print changes made to the system image by PATCH commands.

.PA[TCH] M[EMTOP] addr
	- Set memory top address (SJ/SB/FB monitors only).

.PA[TCH] M[EMTOP] SWR
	- Halt the system after boot and allow you to select top address
	  via console switches, then continue to boot the system.

.PA[TCH] M[EMTOP] AUT[O]
.PA[TCH] M[EMTOP]
	- Reset the changes made by PATCH MEMTOP command.

.PA[TCH] S[UFFIX] x
	- Set suffix for all device handlers.

.PA[TCH] S[UFFIX]
	- Clear device handler suffix.

.REM[OVE] dd[:]
	- Remove device handler.

.RES[ET]
	- Cancel all changes not yet saved via SAVE command.

.SAV[E]
	- Save changes to the system image.

.SE[T] CLI [NO]CCL
	- Enable/disable CCL commands (RT-11 V5.2 and newer)

.SE[T] CLI [NO]DCL
	- Enable/disable DCL commands (RT-11 V5.2 and newer)

.SE[T] CLI [NO]UCF
	- Enable/disable UCF (RT-11 V5.2 and newer)

.SE[T] CLI [NO]UCL
	- Enable/disable UCL (RT-11 V5.2 and newer)

.SE[T] CLO[CK] 50
.SE[T] CLO[CK] 60
	- Set system clock frequency.

.SE[T] ED[IT] EDI[T]
.SE[T] ED[IT] KED
.SE[T] ED[IT] KEX
.SE[T] ED[IT] K13
.SE[T] ED[IT] K52
.SE[T] ED[IT] TEC[O]
	- Set text editor for EDIT command.
	  KEX is suppurted in RT-11XM/XB/ZM/ZB V5.0 and newer.
	  K13 is supported in FODOS system only (instead of K52).

.SE[T] ER[ROR] ERR[OR]
.SE[T] ER[ROR] FAT[AL]
.SE[T] ER[ROR] NON[E]
.SE[T] ER[ROR] SEV[ERE]
.SE[T] ER[ROR] UNC[ONDITIONAL]
.SE[T] ER[ROR] WAR[NING]
	- Set command file abort error level.

.SE[T] EX[IT] [NO]SWA[P]
	- Enable/disable swapping of a program after exit
	  (RT-11 V5.0 and newer).

.SE[T] F[ORTRAN] F4
.SE[T] F[ORTRAN] F77
	- Set default FORTRAN compiler (RT-11 V5.5 and newer).

.SE[T] K[MON] [NO]IND
	- Set default command file mode (RT-11 V5.0 and newer).

.SE[T] R[UN] [NO]VBG[EXE]
	- Enable/disable VBGEXE mode (RT-11XM/XB/ZM/ZB V5.6 and newer).

.SE[T] U[SR] [NO]SWA[P]
	- Enable/disable swapping of USR.

.SE[T] W[ILDCARD] EXP[LICIT]
.SE[T] W[ILDCARD] IMP[LICIT]
	- Set wildcard processing mode for KMON.

.SE[T] TT[n][:] CSR=xxxxxx
.SE[T] TT[n][:] VEC[TOR]=xxx
	- Set terminal CSR and interrupt vector.

.SE[T] TT[:] CONSOL=n
	- Set console terminal line.

.SE[T] TT[:] [NO]QUIET
	- Enable/disable quiet command file mode.

.SE[T] TT[n][:] [NO]CRL[F]
.SE[T] TT[n][:] [NO]FB
.SE[T] TT[n][:] [NO]FOR[M]
.SE[T] TT[n][:] [NO]PAG[E]
.SE[T] TT[n][:] [NO]SCO[PE]
.SE[T] TT[n][:] SPE[ED]=n
.SE[T] TT[n][:] [NO]TAB[F]
.SE[T] TT[n][:] WID[TH]=n
	- Set terminal parameters.

.SH[OW]
	- Show installed device table.

.SH[OW] A[LL]
	- Show all.

.SH[OW] C[ONFIGURATION]
	- Show system configuration.

.SH[OW] T[ERMINALS]
	- Show terminal lines.

.TI[ME] [hh:mm:ss]
	- Show/set system time.