>MOU MU:/FOR/NOWR >MOU DU3:/FOR >BRU /INI MU: DU3: BRU - Starting Tape 1 on MU0: BRU -- *WARNING* -- No bad block data file found BRU - This disk will not contain a hardware bootable system BRU - End of Tape 1 on MU0: BRU - Completed >DMO /USER DMO -- TT0: dismounted from DU3: *** Final dismount initiated *** 23:52:28 *** DU3: -- Dismount complete DMO -- TT0: dismounted from MU0: *** Final dismount initiated *** 23:52:28 *** MU0: -- Dismount complete >MOU DU3:/OVR >ASN DU3:=SY: >SET /DEF=[200,200] >@SYSGEN >; >; RSX-11M-PLUS SYSGEN BL40 >; >; COPYRIGHT (c) 1987 >; DIGITAL EQUIPMENT CORP., MAYNARD MA., 01754 >; >SET /DPRO=[RWED,RWED,RWE,R] >; >; To exit from the SYSGEN procedure at any time, type CTRL/Z. >; >; If you are unsure of the answer to a question for which a de- >; fault answer exists, use the default answer. >; >; >; >;=================================================== >; Choosing SYSGEN Options 12-AUG-04 at 23:52 >;=================================================== >; >; >; >; Every question is preceded by a question number (for example SU010) >; which you can use to find the explanation of the question in the >; RSX-11M-PLUS System Generation and Installation Guide. >; >; An explanation of every question is also available by pressing >; the ESC key (or the ALTMODE key) in response to the question. >; >; If you are unfamiliar with the SYSGEN procedure, the explanation of >; each question can be printed automatically before the question. >; >* SU010 Do you always want the explanation printed? [Y/N D:N]: Y >; >; SYSGEN always creates saved answer files containing your responses >; to the SYSGEN questions: >; >; SYSGENSA1.CMD Setup questions, Executive options >; SYSGENSA2.CMD Peripheral configuration >; SYSGENSA3.CMD Nonprivileged task builds >; >; You should perform a PREPGEN first to create saved answer files, and >; then perform a SYSGEN, specifying those saved answer files as input >; to the Executive, peripheral, and nonprivileged task build sections. >; >; If you have performed a SYSGEN (or PREPGEN) before, you can use the >; saved answer file created during that SYSGEN as input to this SYSGEN. >; SYSGEN uses the saved answers as your responses to the Executive >; questions. >; >* SU020 Do you want to use a saved answer file as input for >* the Executive options? [Y/N D:N]: >; >* SU040 Do you want to use a saved answer file as input for >* the peripheral configuration? [Y/N D:N]: >; >* SU060 Do you want to use a saved answer file as input for >* the nonprivileged task builds? [Y/N D:N]: >; >; A PREPGEN allows you to answer all the SYSGEN questions and create >; saved answer files without actually generating a system: no MCR >; commands are executed, no files are deleted, and the Executive is >; not assembled or built. >; >; After you have successfully completed a PREPGEN, you can perform a >; SYSGEN using the saved answer files from the PREPGEN. The SYSGEN >; will then run unattended. >; >* SU080 Do you want to do a PREPGEN? [Y/N D:N]: >; >; You should have a disk spinning in a disk drive which is a copy of >; your distribution kit. This is your target system disk, the disk on >; which you will perform the SYSGEN. This disk should already be >; mounted with the MOUNT command so that you have access to it. >; >; Enter the name of the drive containing this disk in the form ddnn:, >; i.e., DB2:. >; >* SU090 Enter the name of the disk drive containing your >* target system disk [ddnn:] [S R:2-5]: DU3: >; >ASN DU3:=IN: >ASN DU3:=OU: >ASN DU3:=LB: >ASN DU3:=WK: >ASN DU3:=TK: >ASN DU3:=BC: >ASN DU3:=LI: >ASN DU3:=OB: >ASN DU3:=EX: >ASN DU3:=MP: >; >; You can: >; >; o do a complete SYSGEN >; >; o continue a previous SYSGEN from where you left off >; >; o do an individual section of SYSGEN >; >; >; A complete SYSGEN consists of: >; >; Choosing Executive options >; Choosing Peripheral Configuration >; >; Assembling the Executive and Drivers >; >; Building the Executive and Drivers >; Building the Privileged Tasks >; Building the Nonprivileged Tasks >; >; Creating the System Image File >; >; If you do not choose to do a complete SYSGEN, you can continue >; a previous SYSGEN from where you left off or do an individual >; section of SYSGEN. >; >* SU120 Do you want to do a complete SYSGEN? [Y/N D:Y]: >; >INS [3,54]MAC/TASK=MACT0 >INS [3,54]PIP/TASK=PIPT0 >INS [3,54]LBR/TASK=LBRT0 >INS [3,54]TKB/TASK=TKBT0 >INS [3,54]VMR/TASK=VMRT0 >; >; >; >;====================================================== >; Choosing Executive Options 12-AUG-04 at 23:53 >;====================================================== >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >; You may now enter a comment describing the system you are building. >; This comment is included in the SYSGENSA1 saved answer file for >; documentation, and is printed out when the saved answer file is >; later used as input. >; >; Enter a comment for inclusion in the SYSGENSA1 saved answer file. >; The comment may contain more than one line. The "V" in the right >; margin below marks the maximum line length. When you are done, >; press RETURN in response to the prompt. >; V >* Comment [S R:0.-55.]: >; >; RSX-11M-PLUS may be run on the following PDP-11 processors: >; >; 11/23-PLUS (also called MicroPDP-11/23 and 11/23-B) >; 11/24 >; 11/44 >; 11/53 >; 11/70 >; 11/73 (also called MicroPDP-11/73) >; 11/83 (also called MicroPDP-11/83) >; 11/84 >; >; LSI-11/73 >; >* CE010 What is your target processor type? [S R:5.-12. D:"11/70"]: >; >; The following RSX-11M-PLUS Executives may be generated: >; >; o Full-functionality Executive >; >; o User-tailored Executive >; >; >; The Full-functionality Executive includes all features of the >; RSX-11M-PLUS operating system that can be used on your processor. >; >; Executive data space support >; User data space support >; Task headers out of pool support >; Extended logical name support >; Supervisor-mode library support >; Fast map facility >; All DIGITAL-supplied drivers are loadable >; ICB pool size of 128. words >; Shadow recording support >; Disk data caching support >; Console driver support >; Accounting support >; Batch processor support >; Queue Manager for spooling >; DIGITAL Command Language and alternate CLI support >; CTRL/C abort support >; High performance FCP >; File windows in secondary pool support >; Decimal version numbers in file specifications >; Virtual terminal support with a default virtual terminal >; unit buffer size of 120. bytes and a maximum of 184. bytes >; Character translation support >; Terminal driver extended I/O support >; Time-out on unsolicited terminal input of 30. seconds >; >; >; The User-tailored Executive will require you to answer at least >; twenty additional questions specifying which standard RSX-11M-PLUS >; features you wish to disable. You should not choose the User-tailored >; Executive unless you need to disable specific RSX-11M-PLUS features. >; >; >; For information and guidelines on generating a User-tailored Executive, >; please refer to the RSX-11M-PLUS System Generation and Installation >; Guide. >; >; If you do not understand the options presented by the system >; generation process when configuring an Executive yourself, please >; select the Full-functionality Executive. >; >; >* CE020 Do you want the Full-functionality Executive? [Y/N D:Y]: >; >; Network software provides the capability of simultaneously >; operating tasks on different systems to establish logical >; communication links and to exchange data. This software is >; not provided with RSX-11M-PLUS, but must be purchased separately. >; >; If you choose this option, DCL and alternate CLI support will >; also be included. >; >* CE120 Do you want support for communications products >* (such as DECnet, PSI, and LAT)? [Y/N D:N]: Y >; >; The system name is an arbitrary six-character name. >; This should be the same as the DECnet node name, if any. >; >* CE130 What is the system name? [S R:0-6 D:"RSXMPL"]: >; >; The IP11 industrial I/O subsystem is a combined software and >; hardware package used for process control and monitoring in >; the industrial and manufacturing environment. It consists >; of an RSX device driver (IPDRV) and a set of FORTRAN-callable >; interface routines, used to interface to a variety of hardware >; I/O modules, including digital sense interrupt, change-of-state, >; digital output, digital-to-analog converter, and analog-to-digital >; converter modules. >; >; See the IP11 I/O Subsystem Software Installation Guide for >; information on installing the software. >; >* CE264 Do you want IP11 industrial I/O subsystem support? [Y/N D:N]: >; >; The Executive Debugging Tool (XDT) provides a subset of ODT-11 >; that runs as a part of the RSX-11M-PLUS Executive. This tool >; allows interactive debugging of Executive modules, I/O drivers, >; and interrupt service routines. Selection of this option also >; includes consistency checks in the dynamic memory routines and >; the loader. >; >; Note: If your system does not have Executive data space support, >; XDT will reduce the size of primary pool. If your system does >; have Executive data space support, XDT does not affect the size >; of pool. >; >* CE270 Do you want to include XDT? [Y/N D:N]: Y >; >; If the system crashes, a message is printed on the crash >; notification device. This device must be a paper tape, >; teletype, or line printer compatible device; that is, the >; device must transmit a single byte at a time. Normally, >; the crash notification device is the console terminal which >; is always at the default CSR address given below. >; >* CE280 Enter the crash notification device CSR >* address [O R:160000-177700 D:177564]: >; >; If the system crashes, you can cause all of memory to be written >; onto a device for later analysis with the Crash Dump Analyzer (CDA). >; >; The device on which the crash dump is written must be selected from >; the following list of devices and cannot be a fixed media device: >; >; DB: DM: MM: >; DD: DR: MS: >; DK: DT: MT: >; DL: DU: MU: >; >; Note: Enter both the device and the logical unit number. >; For example, MM0: or DL1:. >; >* CE290 On what device and unit do you want crash dumps >* to be written? [S R:2-6]: MU0: >; >; The minimum supported memory size is 128K words for >; an RSX-11M-PLUS system. The maximum memory size is 1920K words. >; >; This value is only used by VMR when it creates the system image >; file. VMR does not allow you to create a partition or load >; anything beyond the end of memory. When the system is booted, >; your actual memory size is calculated and overrides the value >; you enter here. >; >* CE310 Enter memory size (in K words) [D R:128.-1920. D:256.]: 512. >; >; The PDP-11 floating point processor is an optional arithmetic >; processor. It performs all floating point arithmetic >; operations and converts data between integer and floating point >; formats. >; >; If you choose floating point processor support, the Executive >; will dynamically determine whether the processor has a floating >; point unit or not. >; >; If you omit this support, the Executive will not support a >; floating point unit. >; >* CE320 Do you want floating point processor support? [Y/N D:N]: Y >; >; RSX-11M-PLUS requires a real-time clock for its operation. The >; KW11-P programmable frequency clock, the KW11-L line frequency >; clock, or the DL11-W line frequency clock/console interface may >; be used. >; >* CE330 Is your system clock programmable (KW11-P)? [Y/N D:N]: >; >; Line frequency is either 50 or 60 Hz. In the U.S.A., line frequency >; is always 60 Hz. >; >* CE350 Is your line frequency 50 Hz? [Y/N D:N]: Y >; >; >; >;============================================================= >; Choosing Peripheral Configuration 12-AUG-04 at 23:53 >;============================================================= >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA2.CMD. >; >; You may now enter a comment describing the system you are building. >; This comment is included in the SYSGENSA2 saved answer file for >; documentation, and is printed out when the saved answer file is >; later used as input. >; >; Enter a comment for inclusion in the SYSGENSA2 saved answer file. >; The comment may contain more than one line. The "V" in the right >; margin below marks the maximum line length. When you are done, >; press RETURN in response to the prompt. >; V >* Comment [S R:0.-55.]: >; >; >; The RH11 and RH70 MASSBUS controllers are the controllers for >; the following devices: >; >; DB: RP04, RP05, RP06 disks >; DR: RM02, RM03, RM05, RM80, RP07 disks >; DS: RS03, RS04 disks >; EM: ML11 semiconductor disk emulator >; MM: TM02, TM03 formatters, TE16, TU16, TU45, TU77 tapes >; >* CP0604 How many RH controllers do you have? [D R:0.-15. D:4.]: 0 >; >; >; DK: controller: RK11 devices: RK05, RK05F >; >; The RK11 cartridge disk drive and control is a complete mass >; storage system for random access data storage. The system >; includes a modular mass storage device utilizing removable >; disk cartridges and a complete, easy-to-program, control unit. >; A disk cartridge holds over 2.4 megabytes. The system is >; expandable up to 8 drives per controller. An RK11 includes a >; controller and the first disk drive. Optionally, the controller >; can support up to four RK05F fixed platter drives each with twice >; the capacity of the standard RK05 drive. >; >* CP2204 How many RK11 cartridge disk controllers do you have? [O D:0]: >; >; >; DM: controllers: RK611, RK711 devices: RK06, RK07 >; >; The RK611/711 is a 3 data surface, removable, random access bulk >; storage system with a storage capacity of 14 megabytes (RK06) or >; 28 megabytes (RK07) per pack. The RK611/711 includes a control >; unit and the first disk pack drive. The system is expandable up >; to eight drives. >; >* CP2404 How many RK611/711 disk cartridge controllers do >* you have? [O D:0]: >; >; >; DL: controllers: RL11, RLV12 devices: RL01, RL02 >; >; The RL11/RLV12 disk subsystem uses a medium performance, RL01/02 >; direct access drive with a single read/write head per surface. >; Each drive provides 5.2 megabytes (RL01) or 10.4 megabytes (RL02) >; of storage on a removable, top-loading cartridge. The subsystem >; is expandable up to four drives. >; >* CP2604 How many RL11/RLV11 disk cartridge controllers do >* you have? [O D:0]: >; >; >; DP: controller: RP11 devices: RP02, RPR02, RP03 >; >; The RP11 is a complete mass storage system using a magnetic >; disk pack with 20 data surfaces and a moving read/write head. >; The RP02 and RPR02 have a capacity of 20 megabytes. The RP03 >; has a capacity of 41 megabytes. >; >* CP2804 How many RP11 disk pack controllers do you have? [O D:0]: >; >; >; DU: controllers: RQDX1, RQDX2, RQDX3, RUX50, RQC25, KDA50, UDA50 >; >; devices: RX33, RX50, RD31, RD51, RD52, RD53, RD54, RC25, >; RA60, RA80, RA81, RA82 >; >; The total of DU and MU controllers cannot be greater than 10. >; >; The MSCP disk controllers are: >; >; RQDX1, RQDX2, RQDX3, RUX50, RQC25, RUC25, KDA50, UDA50 >; >; These intelligent disk controllers provide enhanced I/O optimization, >; error correction capability, and, in some cases, dynamic bad block >; handling. >; >* CP3004 How many MSCP disk controllers do you have? [D R:0.-10. D:0.]: 2. >; >; The MSCP disk drives are: >; >; RX33, RX50, RD31, RD51, RD52, RD53, RD54 >; RC25, RA60, RA80, RA81, RA82 >; >; The RX50 contains two 5.25 inch floppy diskettes with a formatted >; capacity of 400 kilobytes each. Count each RX50 (with two >; diskettes) as two drives. >; >; The RD51 is a 5.25 inch fixed media, Winchester technology disk >; with a formatted capacity of 10 megabytes. >; >; The RD52 is a 5.25 inch fixed media Winchester technology disk >; with a formatted capacity of 31 megabytes. >; >; The RD53 is a 5.25 inch fixed media Winchester technology disk >; with a formatted capacity of 71 megabytes. >; >; The RC25 contains a fixed and removable disk on the same spindle >; with a formatted capacity of 25 megabytes each. Count each RC25 >; (with two disks: one fixed, one removable) as two drives. >; >; The RA60 is a removable media disk with a formatted capacity of >; 205 megabytes. >; >; The RA80 is a fixed media, Winchester technology disk with a >; formatted capacity of 121 megabytes. >; >; The RA81 is a fixed media, Winchester technology disk with a >; formatted capacity of 456 megabytes. >; >; Enter the total number of MSCP disk drives in your system. >; >* CP3008 How many MSCP disk drives do you have? [D R:1.-8. D:1.]: 8. >; >; >; The physical unit number of a drive is the number shown on the >; unit number plug (or other indicator) on the drive. >; >* CP3036 What is the physical unit number of DU0:? [O R:0-377 D:0]: >; >; The legal characters in a controller specification are: >; >; A and B >; >* CP3044 To which DU controller is DU0: connected? [S R:1-1]: A >; >; >* CP3036 What is the physical unit number of DU1:? [O R:0-377 D:1]: >; >* CP3044 To which DU controller is DU1: connected? [S R:1-1]: A >; >; >* CP3036 What is the physical unit number of DU2:? [O R:0-377 D:2]: >; >* CP3044 To which DU controller is DU2: connected? [S R:1-1]: A >; >; >* CP3036 What is the physical unit number of DU3:? [O R:0-377 D:3]: >; >* CP3044 To which DU controller is DU3: connected? [S R:1-1]: A >; >; >* CP3036 What is the physical unit number of DU4:? [O R:0-377 D:4]: 0 >; >* CP3044 To which DU controller is DU4: connected? [S R:1-1]: B >; >; >* CP3036 What is the physical unit number of DU5:? [O R:0-377 D:5]: 1 >; >* CP3044 To which DU controller is DU5: connected? [S R:1-1]: B >; >; >* CP3036 What is the physical unit number of DU6:? [O R:0-377 D:6]: 2 >; >* CP3044 To which DU controller is DU6: connected? [S R:1-1]: B >; >; >* CP3036 What is the physical unit number of DU7:? [O R:0-377 D:7]: 3 >; >* CP3044 To which DU controller is DU7: connected? [S R:1-1]: B >; >; >; Enter the vector address for this controller. This vector address >; can be changed after the SYSGEN by using the VMR CON SET command. >; >* CP3068 Enter the vector address of DUA [O R:60-774 D:154]: >; >; Enter the CSR address for this controller. This CSR address can >; be changed after the SYSGEN by using the VMR CON SET command. >; >* CP3072 What is its CSR address? [O R:160000-177700 D:172150]: >; >; >; Enter the vector address for this controller. This vector address >; can be changed after the SYSGEN by using the VMR CON SET command. >; >* CP3068 Enter the vector address of DUB [O R:60-774]: 354 >; >; Enter the CSR address for this controller. This CSR address can >; be changed after the SYSGEN by using the VMR CON SET command. >; >* CP3072 What is its CSR address? [O R:160000-177700]: 160334 >; >; >; MU: controllers: TK50, TU81, TU81E, TQ81E >; >; The TMSCP tape controllers are: >; >; TK50, TU81, TU81E, TQ81E >; >; >* CP3404 How many TMSCP tape controllers do you have? [D R:0.-8. D:0.]: 1 >; >; >; The physical unit number of a drive is the number shown on the >; unit number plug (or other indicator) on the drive. >; >* CP3436 What is the physical unit number of MU0:? [O R:0-377 D:0]: >; >; >; Enter the vector address for this controller. This vector address >; can be changed after the SYSGEN by using the VMR CON SET command. >; >* CP3468 Enter the vector address of MUA [O R:60-774 D:260]: >; >; Enter the CSR address for this controller. This CSR address can >; be changed after the SYSGEN by using the VMR CON SET command. >; >* CP3472 What is its CSR address? [O R:160000-177700 D:174500]: >; >; >; CR: controllers: CM11, CR11 >; >; The CR11 card reader reads EIA standard 80-column punched data >; cards at 300 cards per minute. It uses a riffle-air and a >; vacuum-pick mechanism to move the cards. The CM11-F reads 80- >; column mark-sense cards, which can have punched holes, at 285 >; cards per minute. >; >* CP4004 How many CM/CR11 card readers do you have? [O D:0]: >; >; >; CT: controller: TA11 device: TU60 >; >; The TA11 magnetic tape cassette system is a dual-drive, >; reel-to-reel unit designed to replace paper tape. Its two >; drives run non-simultaneously using proprietary Digital >; Equipment Corporation Philips-type cassettes. The TA11 >; includes a control unit and a dual tape transport. >; >* CP4204 How many TA11 dual cassettes do you have? [O D:0]: >; >; >; MS: controllers: TS11, TU80, TSV05, TK25 >; >; The TS11, TU80, and TSV05 are 1/2 inch 1600 bpi tape subsystems >; and the TK25 is a cartridge tape subsystem. >; >* CP4404 How many TS11/TU80/TSV05/TK25 >* magtape controllers do you have? [O D:0]: >; >; >; DT: controller: TC11 device: TU56 >; >; The TC11 is a dual-unit bidirectional magnetic-tape transport >; system for auxiliary data storage. >; >; The system stores information at fixed positions on magnetic >; tape as in magnetic disk or drum storage devices, rather than >; at unknown or variable positions as in conventional magnetic >; tape systems. >; >; A DECtape system consists of up to 4 dual transports, a control >; unit (which will buffer and control information for up to four >; dual transports). A TC11 includes a control unit and the >; first dual tape transport. >; >* CP4604 How many TC11 DECtape controllers do you have? [O D:0]: >; >; >; DX: controller: RX11 device: RX01 >; >; The RX11 is an industry compatible disk storage system for >; flexible (floppy) disks. An RX11 is capable of controlling two >; flexible disk drives each having a capacity of 256K bytes. >; >* CP4804 How many RX11 disk controllers do you have? [O D:0]: >; >; >; DY: controller: RX211, RXV21 device: RX02 >; >; The RX211 and RXV21 are single or double density flexible (floppy) disk >; controllers with a storage capacity of 256K bytes (single density) or >; 512K bytes (double density). One controller is capable of controlling >; two drives. >; >* CP5004 How many RX211/RXV21 disk controllers do you have? [O D:0]: >; >; >; DD: controller: DL11 device: TU58 >; >; The TU58 driver interfaces with the 3M DC-100A tape >; cartridge drive and controller units via a parallel to ser- >; ial DL11 converter at baud rates up to 9.6K. Data is >; stored on the media on two parallel tracks recorded in the >; same direction. The tape is preformatted into 2048 physical >; records of 128 bytes each. Access to these physical records >; is by groups of four corresponding to a standard DEC block >; of 512 bytes. >; >* CP5204 How many TU58 controllers do you have? [O D:0]: >; >; >; LP: controllers: LA180, LN01, LP11, LS11, LV11 >; devices: LA180, LN01, LP01, LP02, LP04, LP05, LP06, >; LP07, LP14, LP25, LP26, LP27, LS11, LV01 >; >; The LP11 is a high-speed impact line printer with a rotating drum >; or band. It is available in a variety of models, with and without >; lowercase characters. >; >; The LS11 line printer is a medium-speed impact dot-matrix line >; printer. It prints at a rate of 165 characters per second at >; 10 characters per inch with up to 132 characters per line. >; >; The LA180 DECprinter is similar to the LS11 with the exception >; that it prints at the rate of 180 characters per second. >; >; The LV11 is a high-speed electrostatic printer-plotter that prints >; at a rate of 500 lines per minute. Only the print option is >; supported under RSX-11M-PLUS. >; >* CP5404 How many LP/LS/LV11/LA180 line printers do you have? [O D:0]: 1 >; >; If a task tries to access the line printer when the device is not >; ready, a message saying the line printer is not ready is printed >; on the console terminal. This message is repeated every n seconds, >; where n is your response to this question, for as long as the line >; printer remains not ready. >; >; Enter zero to disable this feature and suppress the messages. >; >* CP5408 Enter the number of seconds between >* line printer-not-ready messages [D R:0.-255. D:15.]: 30. >; >; Enter the vector address for this line printer. This vector address >; can be changed after the SYSGEN by using the VMR CON SET command. >; >* CP5468 Enter vector address of the next line >* printer [O R:60-774 D:200]: >; >; Enter the CSR address for this line printer. This CSR address can >; be changed after the SYSGEN by using the VMR CON SET command. >; >* CP5472 What is its CSR address? [O R:160000-177700 D:177514]: >; >; Here is a table of the valid line printer types and their >; characteristics: >; >; printer # of lines per supports >; type controller columns minute optimization >; >; LA180 LA180 132 150 no >; LN01 LN01 132 600 NA >; LP01 LP11-F/H 80 170-1110 yes >; LP02 LP11-J/K 132 170-1110 yes >; LP04 LP11-R/S 132 1110 yes >; LP05 LP11-V/W 132 300 no >; LP06 LP11-Y/Z 132 460-600 no >; LP07 LP11-G 132 1200 no >; LP14 LP11-C/D 132 660-900 no >; LP25 LP11-A/B 132 215-300 no >; LP26 LP11-E 132 445-600 no >; LP27 LP11-U 132 800-1200 no >; LS11 LS11 132 60-200 no >; LV01 LV11 132 500 yes >; >; The printer type is used to set two characteristics in the UCB: >; >; o Column or buffer width >; >; This is settable in VMR or MCR with the SET /BUF command. >; >; >; o Fast line printer support >; >; This is an optimization performed by the driver to eliminate >; unnecessary print cycles. This characteristic is not settable >; in VMR or MCR. >; >; If you specify the wrong printer type and the driver performs >; the optimization for a printer that does not support it, you >; will occasionally lose a line of a listing when the printer >; is taken off line. >; >; If you specify the wrong printer type and the driver does not >; perform the optimization for a printer that supports it, the >; printer will run a little slower than it would with the >; optimization, but there will be no other adverse effects. >; >; If you do not know the correct printer type for your printer, take >; the default. This will give you a 132-column printer without fast >; printer optimization. Once your system is running, you can change >; the number of columns if necessary with the MCR SET command. >; >* CP5480 Enter line printer type for LPA [S R:4-5 D:"LP25"]: >; >; If this line printer has both uppercase and lowercase characters, >; answer Yes to this question. If it only has uppercase characters, >; answer No. Your answer determines the initial setting for >; lowercase character conversion on this printer. You can change >; this at any time by using the MCR SET /LOWER command. >; >* CP5484 Does LPA have lowercase characters? [Y/N D:N]: >; >; >; MT: controllers: TM11, TMA11, TMB11 devices: TE10, TU10, TU10W, TS03 >; >; The TM/TMA/TMB11 is a magnetic tape system ideally suited for >; writing, reading, and storing large volumes of data and >; programs in a serial manner. The system reads and writes in >; industry-compatible format. TU10 drives support 10.5-inch reels >; containing up to 2400 feet of tape upon which over 180 million >; bits of data can be stored on high density 9-track tape. TS03 >; drives support 7-inch reels containing up to 600 feet of tape in >; high density 9-track format. TU10W drives are compatible with >; TU10 drives except they operate only on 800 bpi, 9-track tape. >; >* CP5604 How many TM/TMA/TMB11 magtape controllers do you have? [O D:0]: >; >; >; PP: controller: PC11 >; >; The PC11 is a high speed paper tape reader/punch that is >; capable of reading eight-hole, unoiled, perforated paper tape at >; 300 characters per second, and punching tape at 50 characters >; per second. >; >* CP5804 How many PC11 paper tape reader/punches do you have? [O D:0]: >; >; >; PR: controller: PR11 >; >; The PR11 is a high speed paper tape reader that is capable of >; reading eight-hole unoiled perforated paper tape at 300 >; characters per second. >; >; >* CP6004 How many PR11 paper tape readers do you have? [O D:0]: >; >; >; LA: controller: LPA11 >; >; The LPA11 lab peripheral accelerator is a real-time subsystem which >; interfaces to the PDP-11 family of computers. The system consists >; of the LPA11, up to 2 A/D converters, a programmable real-time >; clock, a D/A converter, and up to five digital I/O modules. >; >* CP6204 How many LPA11 lab subsystems do you have? [D R:0.-16. D:0.]: >; >; >; TT: controllers: DL11, DLV11 controller mnemonic: YL >; >; The DL11/DLV11 series of asynchronous single line interfaces handle >; full or half-duplex communication between a wide variety of serial >; communication channels and a PDP-11 computer. >; >; SYSGEN automatically sets up the data bases for all mandatory >; DL11/DLV11s. (For each processor in the system, there must be a >; DL11/DLV11; these are mandatory.) Answer the next question with >; the number of additional DL11/DLV11s in your system. >; >; Note: Enter only the number of DL11s used as terminal interfaces. >; Do not include any DL11s used as controlers for the TU58 DECtape II. >; >* CP6804 Enter number of additional DL11/DLV11 line interfaces [O D:0]: >; >; The terminal types supported by RSX-11M-PLUS SYSGEN are: >; >; ASR33 LA12 VT05B >; ASR35 LA30P VT50 >; LA30S VT52 >; DTC01 LA34 VT55 >; LA36 VT61 >; KSR33 LA38 VT100 >; LA50 VT101 >; LA100 VT102 >; LA120 VT105 >; LA180S VT125 >; LA210 VT131 >; LN03 VT132 >; PC3xx VT2xx >; >* CP6832 Enter terminal type for YLA [S R:4-6 D:"LA120"]: VT100 >; >; >; TT: controller: DH11 controller mnemonic: YH >; >; The DH11 multiplexer connects the PDP-11 with 16 asynchronous >; serial communications lines operating with individually >; programmable parameters. These parameters are: >; >; transmitter speed (baud) >; receiver speed (baud) >; >* CP7004 Enter number of DH11 asynchronous line >* multiplexers [D R:0.-16. D:0.]: >; >; >; TT: controller mnemonic: YV >; >; controllers: DHU11, DHV11, CXA16, CXB16, CXY08 >; >; >; These multiplexers connect the PDP-11 with up to >; 16 (DHU11, CXA16, CXB16) or 8 (DHV11, CXY08) >; asynchronous serial communications lines operating with >; individually programmable parameters. These parameters are: >; >; transmitter speed (baud) >; receiver speed (baud) >; >; Modem control is available with the DHU11, DHV11 and CXY08. >; The CXA16 and CXB16 do not support modem control. Use the VMR >; or MCR SET /REMOTE commands in order to enable dialup lines. >; >* CP7104 Enter number of DHU11/DHV11/CXA16/CXB16/CXY08 (YV:-type) >* asynchronous line multiplexers [D R:0.-16. D:0.]: 1 >; >; Support for remote (dial-up) lines: >; >; DHU11, DHV11, and CXY08 controllers support modem control. >; Modem control is not supported by the CXA16 and CXB16. >; >; Since it is not possible to tell which YV: controllers in your >; configuration might support remote lines, SYSGEN cannot automatically >; enable any lines as remote. You should use the VMR or MCR command >; SET /REMOTE command to enable lines as remote. You may wish to >; pause and edit VMRTTY.CMD at the end of this SYSGEN to add those >; VMR commands. >; >* CP7120 Enter total number of YV: controller dial-up lines [D R:0.-16. D:0.]: 16. >; >; The valid baud rates are: >; >; 75 >; 110 >; 134.5 >; 150 >; 300 >; 600 >; 1200 >; 1800 >; 2000 >; 2400 >; 4800 >; 9600 >; 19200 >; >* CP7128 At which baud rate do you want to answer? [S R:2-5 D:"300"]: 9600 >; >; The vector address for each YV: controller is assigned from the >; floating vector space starting at 300. The vector address can be >; changed after the SYSGEN by using the VMR CON SET command. >; >* CP7168 Enter vector address of YVA [O R:300-770]: 300 >; >; The CSR address for each YV: controller is assigned from the floating >; address space starting at 160010. The CSR address can be changed >; after the SYSGEN by using the VMR CON SET command. >; >* CP7172 What is its CSR address? [O R:160000-177700]: 160440 >; >; Each DHV11 or CXY08 multiplexer supports up to 8 lines, and >; each DHU11, CXA16 or CXB16 multiplexer can support up to 16 lines. >; You can specify less than the maximum allowed by the hardware device, >; but another SYSGEN will be required to add lines beyond the number >; specified in response to this question. Thus it is advisable to >; respond with the maximum allowed by the device. >; >* CP7176 How many lines does YVA support? [D R:1.-16. D:16.]: >; >; The terminal types supported by RSX-11M-PLUS SYSGEN are: >; >; ASR33 LA12 VT05B >; ASR35 LA30P VT50 >; LA30S VT52 >; DTC01 LA34 VT55 >; LA36 VT61 >; KSR33 LA38 VT100 >; LA50 VT101 >; LA100 VT102 >; LA120 VT105 >; LA180S VT125 >; LA210 VT131 >; LN03 VT132 >; PC3xx VT2xx >; >* CP7184 Enter terminal type for YVA [S R:4-6 D:"VT100"]: >; >; >; TT: controller: DJ11 controller mnemonic: YJ >; >; The DJ11 is a multiplexed interface between 16 asynchronous >; serial data-communications channels and the PDP-11 UNIBUS. The >; DJ11 is a unit whose character formats and operating speeds are >; jumper or strap selectable in groups of four lines. >; >* CP7204 Enter number of DJ11 asynchronous line >* multiplexers [D R:0.-15. D:0.]: >; >; >; TT: controllers: DZ11, DZQ11, DZV11, DFA01 controller mnemonic: YZ >; >; The DZ11/DZQ11/DZV11/DFA01 multiplexers connect the PDP-11 with up to >; 8 asynchronous serial communications lines operating with individually >; programmable parameters. These parameters are: >; >; Transmitter speed / Receiver speed (baud) >; >* CP7404 Enter number of DZ11/DZQ11/DZV11/DFA01 asynchronous line >* multiplexers [D R:0.-30. D:0.]: >; >; SYSVMR.CMD, the VMR command file which creates your system image file, >; contains commands that set the characteristics for each terminal as >; follows: >; >; Terminal type: as you specified for the controller >; Buffer width: 80 >; Speed: 300/300 for hardcopy terminals >; 9600/9600 for CRTs >; Lower to upper- >; case conversion: No for hardcopy terminals >; Yes for CRTs >; >; If you wish to change these characteristics for your terminals, SYSGEN >; will allow you to edit SYSVMR.CMD. >; >; >; >; Intercomputer communication devices consist of the following: >; >; PCL11 full-duplex DMA interprocessor communications >; device >; DMC11/DMR11 high-speed synchronous serial line interface >; DUP11 synchronous serial line interface >; DEUNA Ethernet communications controller >; >; Note: Do NOT include any devices which will be used with DECnet. >; Those devices should be included when you do your NETGEN. >; >* CP7604 Do you have any intercomputer communication devices? [Y/N D:N]: >; >; >; Enter device mnemonics for any user-supplied drivers. The driver >; source files must reside in [11,10] and be named ddDRV.MAC and >; ddTAB.MAC where dd is the device mnemonic. >; >; You may enter the mnemonics on more than one line. When you have >; listed all the drivers, press RETURN when asked for the device >; mnemonic. >; >; The device mnemonic must not include a colon. >; >* CP9604 Enter device mnemonics for user-supplied drivers [S]: >; >; >; If you will be adding other devices after this SYSGEN or have >; included user-supplied devices, you will want to set the highest >; interrupt vector address high enough to accommodate the vectors for >; those devices. >; >; The highest vector among the devices you specified in this SYSGEN >; is 374(octal). This is the default response for this question. >; >* CP9632 What is the highest interrupt vector >* address? [O R:374-774 D:374]: 774 >; >; >; >;================================================================ >; Assembling the Executive and Drivers 12-AUG-04 at 23:58 >;================================================================ >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >PIP RSXMC3.MAC=RSXMC1.MAC,RSXMC2.MAC >PIP RSXMC.MAC=RSXMC3.MAC,RSXMC0.MAC >; >; Copy the files created by the Executive options and peripheral >; configuration sections into the correct directories. >; >SET /UIC=[1,24] >PIP [11,10]/NV=[200,200]RSXMC.MAC >PIP [11,10]/NV=[200,200]SYSTB.MAC >UFD SY:[11,24] >PIP [11,24]/NV=[200,200]RSXASM.CMD >PIP [11,24]/NV=[200,200]DRIVERS.ASM >; >; >; Assembly listings of the Executive modules and the drivers can be >; generated and stored in a file or printed directly. >; >; Generating listings is time-consuming and they are not normally >; needed, so we recommend you answer No to this question. >; >* AE010 Do you want assembly listings of the Executive and >* drivers? [Y/N D:N]: >; >ASN NL:=LS: >; >; >; If you are building a specialized system you may wish to edit >; some of the files which SYSGEN produced before the Executive >; and drivers are assembled. >; >* AE030 Do you wish to pause to edit any files before >* assembling? [Y/N D:N]: >; >SET /UIC=[11,24] >; >; Now we assemble the Executive and resident drivers. >; >PIP *.OBJ;*/DE/NM,*.TTY;* >; >TIME 23:59:11 12-AUG-04 >; >MAC @RSXASM >; >; Now we assemble the loadable drivers. >; >TIME 00:04:33 13-AUG-04 >; >MAC @DRIVERS.ASM >; >TIME 00:07:26 13-AUG-04 >; >; Now we build the concatenated object module file for the Executive. >; >PIP RSX11M.OBS=*.OBJ >PIP TTDRV.OBS=*.TTY >; >SET /UIC=[200,200] >PIP /NV=[11,10]RSXMC.MAC >; >SET /UIC=[1,24] >PIP RSXBLD.CMD/PU/NM >PIP RSX11M.OLB;*/DE/NM >PIP [200,200]RSXMC.MAC/PU/NM >; >; Now we build the Executive library. >; >LBR RSX11M/CR:256.::256./-EP=[11,24]RSX11M.OBS >PIP [11,24]RSX11M.OBS;*,*.OBJ;*/DE >; >; Now we build the terminal driver library. >; >LBR TTDRV/CR:40.:392.:128.=[11,24]TTDRV.OBS >PIP [11,24]TTDRV.OBS;*,*.TTY;*/DE >SET /UIC=[200,200] >; >; >; >;============================================================== >; Building the Executive and Drivers 13-AUG-04 at 00:08 >;============================================================== >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >; >; Allocate space to be used later for the system image file. >; >SET /UIC=[1,54] >PIP RSX11M.TMP/CO/BL:1026.=NL: >; >SET /UIC=[200,200] >; >SET /UIC=[1,24] >SET /UIC=[200,200] >SET /UIC=[1,54] >PIP SYSVMR.CMD=[200,200]SYSVMR.CMD,VMRTTY.CMD >; >SET /UIC=[200,200] >; >; At this point, you can edit: >; >; the Executive task-build command files in [200,200] >; the driver task-build command files in [200,200] >; the privileged task task-build command files in [1,24] >; SYSVMR.CMD in [1,54] >; >; In most cases there is no need to edit the task-build command files. >; However, you may want to tailor SYSVMR for your system. >; >* BE030 Do you want to pause to edit any files before >* task-building? [Y/N D:N]: >; >SET /UIC=[1,24] >PIP [1,24]/NV/NM=[200,200]RSXBLD.CMD,RSX11M,DSP11M,LDR11M >PIP [1,24]/NV=[200,200]DIR11M.CMD,DR211M,DIRCOM,DR2COM,DIR >PIP [1,24]/NV=[200,200]DR311M.CMD,DR411M,DR3COM,DR4COM >PIP [1,24]/NV=[200,200]VEC11M.CMD,DCM11M,VECCOM >; >; Now we build the Executive. >; >TIME 00:09:02 13-AUG-04 >; >TKB @RSXBLD >; >; Now we build the loadable drivers >; >TIME 00:10:23 13-AUG-04 >; >TKB @[200,200]DRIVERS.BLD >; >TIME 00:11:08 13-AUG-04 >SET /UIC=[200,200] >; >; >; >;========================================================= >; Building the Privileged Task 13-AUG-04 at 00:11 >;========================================================= >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >; >; Maps of the privileged tasks can be generated and stored in a file >; or printed directly. >; >; Maps of the privileged tasks are not normally needed, so we >; recommend you answer No to this question. >; >* BP040 Do you want the maps of the privileged tasks? [Y/N D:N]: >; >ASN NL:=MP: >; >SET /UIC=[1,24] >; >TIME 00:11:13 13-AUG-04 >; >TKB @SAVBLD >; >TIME 00:11:31 13-AUG-04 >; >ASN LB:=OU: >SET /UIC=[200,200] >; >; >; >;============================================================ >; Rebuilding Supplied System Tasks 13-AUG-04 at 00:11 >;============================================================ >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA3.CMD. >; >; >; All nonprivileged and vectored privileged system tasks are supplied >; already task-built and can be found in the library UFD on the target >; system disk. It is not normally necessary to rebuild these supplied >; system tasks although you may wish to do so, for example if one of >; them has been patched. >; >* BN010 Do you want to rebuild any system tasks? [Y/N D:N]: Y >; >; You may now enter a comment describing the system you are building. >; This comment is included in the SYSGENSA3 saved answer file for >; documentation, and is printed out when the saved answer file is >; later used as input. >; >; Enter a comment for inclusion in the SYSGENSA3 saved answer file. >; The comment may contain more than one line. The "V" in the right >; margin below marks the maximum line length. When you are done, >; press RETURN in response to the prompt. >; V >* Comment [S R:0.-55.]: >; >; FCSRES is a resident library of commonly used FCS routines. >; Tasks can be built to map to the FCS routines in FCSRES instead of >; including the FCS routines in their task image. This saves physical >; memory because the many separate copies of the FCS routines in >; different task images are replaced by one copy in the library which >; all the tasks use. >; >; FCSFSL uses the FCSRES library mapped as a supervisor-mode library. >; In addition to the saving of physical memory, the supervisor-mode >; library also saves virtual address space since the FCS routines >; are mapped using the supervisor mode APRs. This frees user-mode >; virtual address space for the application task. This can be used >; to reduce overlay activity, for example. >; >; SYSGEN can build many of the system tasks to use the FCS resident >; libraries if you desire. If you answer "Yes" to the following >; question SYSGEN will use FCSFSL and FCSRES wherever possible. If you >; answer "No" to this question SYSGEN will only use FCSFSL or FCSRES >; when you explicitly include it in the task specification. >; >* [Y] BN012 Use the FCSRES and FCSFSL libraries? [Y/N]: Y >; >; The following supplied system tasks and utilities can be rebuilt at this time : >; >; The letters "R" and "F" in parentheses following the task name indicate that >; versions may be built to use FCSRES and FCSFSL respectively. >; >; ACC (R&F) CRP HEL (R&F) MTA SLP (R&F) >; ACD DCL HRC PAT (R&F) STK (F) >; ACNT (R&F) DLD ICM (R&F) PIP (R&F) SYL (R&F) >; ACS (R&F) DMO INI PMD (R&F) TDX >; BAD DMP (R&F) INS PMT TKB (R&F) >; BOO DSC IPP (R&F) PSW TKN >; BRO DTE IOX (R&F) QMG (R&F) UFD >; BRU EDI (R&F) LBR (R&F) QMGCLI UML >; BYE EDT (R&F) LOA QMGPRT UNL (R&F) >; CDA (R&F) ELI (R&F) LPP (R&F) RCT VFY (R&F) >; CFL (F) ERL MAC (R&F) RMD VMR >; CMP (R&F) FLX (R&F) MCD RPT (F) XDT >; CON FMT MCR SHA ZAP (R&F) >; COT (R&F) FTB (R&F) MFT SHF >; CRF (R&F) FXR MOU SHU >; >; Press ESC for the list of the nonprivileged utilities and >; vectored privileged system tasks that may be rebuilt here. >; >; Enter ALL to build all the tasks, using FCSFSL and FCSRES. >; Enter ALLVAN to build all non-FCSRES and non-FCSFSL tasks. >; Enter ALLRES to build all the FCSRES tasks. >; Enter ALLFSL to build all the FCSFSL tasks. >; >; SYSGEN will attempt to use FCSFSL and FCSRES where possible. >; >; Enter the task names separated by commas. You can enter them on >; more than one line. When you are done, finish the list with a >; period or press RETURN in response to the prompt. >; >* BN020 Enter task name(s) [S]: ALL >* BN020 Enter task name(s) [S]: >; >; >SET /UIC=[1,24] >SET /UIC=[200,200] >; >; Maps of the system tasks can be generated and stored in a file >; or printed directly. >; >; Maps of the system tasks are not normally needed, so we >; recommend you answer No to this question. >; >* BN030 Do you want the maps of the system tasks? [Y/N D:N]: >; >ASN NL:=MP: >; >; At this point, you can edit the system task task-build command >; files in [1,24]. In most cases there is no need to edit these files. >; >* BN050 Do you want to pause to edit any files before >* task-building? [Y/N D:N]: >SET /UIC=[1,24] >; >; Now we will build the requested system tasks. >; >; >TKB @ACDBLD >TKB @BADBLD >TKB @BOOBLD >TKB @BROBLD >TKB @BRUBLD >TKB @BYEBLD >TKB @CONBLD >TKB @CRPBLD >TKB @DCLBLD >TKB @DLDBLD >TKB @DMOBLD >TKB @DSCBLD >TKB @DTEBLD >TKB @ERLBLD >TKB @FMTBLD >TKB @FXRBLD >TKB @HRCBLD >TKB @INIBLD >TKB @INSBLD >TKB @LOABLD >TKB @MCDBLD >TKB @MCRBLD >TKB @MFTBLD >TKB @MOUBLD >TKB @MTABLD >TKB @PMTBLD >TKB @PSWBLD >TKB @QCLBLD >TKB @QPRBLD >TKB @RCTBLD >TKB @RMDBLD >TKB @SHABLD >TKB @SHFBLD >TKB @SHUBLD >TKB @TDXBLD >TKB @TKNBLD >TKB @UFDBLD >TKB @UMLBLD >TKB @VMRBLD >TKB @XDTBLD >TKB @ACCFSLBLD >TKB @ACNFSLBLD >TKB @ACSFSLBLD >TKB @CDAFSLBLD >TKB @CFLFSLBLD >TKB @CMPFSLBLD >TKB @COTFSLBLD >TKB @CRFFSLBLD >TKB @DMPFSLBLD >TKB @EDIFSLBLD >TKB @EDTFSLBLD >TKB @ELIFSLBLD >TKB @FLXFSLBLD >TKB @FTBFSLBLD >TKB @HELFSLBLD >TKB @ICMFSLBLD >TKB @IPPFSLBLD >TKB @IOXFSLBLD >TKB @LBRFSLBLD >TKB @LPPFSLBLD >TKB @MACFSLBLD >TKB @PATFSLBLD >TKB @PIPFSLBLD >TKB @PMDFSLBLD >TKB @QMGFSLBLD >TKB @RPTFSLBLD >TKB @SLPFSLBLD >TKB @STKFSLBLD >TKB @SYLFSLBLD >TKB @TKBFSLBLD >TKB @UNLFSLBLD >TKB @VFYFSLBLD >TKB @ZAPFSLBLD >; >SET /UIC=[200,200] >; >; >; >;========================================================== >; Creating the System Image File 13-AUG-04 at 00:34 >;========================================================== >; >; >SET /UIC=[1,54] >; >PIP RSX11M.TMP;*/DE/NM >; >PIP RSX11M.SYS/CO/NV/BL:1026.=RSX11M.TSK >; >ASN LB:=SY: >; >; Utility tasks stay in utility UFD [3,54]. >; >; RSX11M.TSK is a backup copy of the Executive you just built. >; >; >; VMR will now initialize the system. >; >VMR @SYSVMR Loading Executive data space Data space loading completed VMR -- *DIAG*-Installed tasks or commons may no longer fit in partition SET /TOP=SYSPAR:-* VMR -- *DIAG*-Loadable driver larger than 4K LOA TT: VMR -- *DIAG*-Installed tasks or commons may no longer fit in partition SET /TOP=DRVPAR:-* SECPOL 117734 00177100 00100000 SEC POOL SYSPAR 117670 00277100 00163200 MAIN 117624 00277100 00110400 RO COM !DIR11M! 117434 00407500 00005200 TASK [...LDR] 117230 00414700 00032200 TASK [MCR...] 117024 00447100 00010000 TASK [TKTN ] 116620 00457100 00003200 TASK [SHF...] DRVPAR 116540 00462300 00124200 MAIN 116474 00462300 00006600 RO COM !TTEXT ! 116410 00471100 00020600 RO COM !TTCOM ! 116324 00511700 00034500 DRIVER (TT:) 116260 00546400 00006200 RO COM !PUCOM ! 115014 00554600 00012600 DRIVER (DU:) 114460 00567400 00011200 DRIVER (MU:) 114240 00600600 00001300 DRIVER (LP:) 114050 00602100 00000100 DRIVER (NL:) 114004 00602200 00000300 DRIVER (CO:) 113740 00602500 00002500 DRIVER (VT:) 113674 00605200 00001300 DRIVER (RD:) GEN 113630 00606500 03171300 MAIN ...LDR 12.01 117500 SYSPAR 248. 00005200 LB0:-00166347 FIXED TKTN 07.00 117070 SYSPAR 248. 00010000 LB0:-00174060 FIXED F11MSG 15.00 111424 GEN 200. 00006200 LB0:-00050326 MTAACP 16.00 111030 GEN 200. 00016200 LB0:-00173731 SHE... 05.01 110560 GEN 200. 00014200 LB0:-00173032 MCR... 06.00 117274 SYSPAR 160. 00032200 LB0:-00172531 FIXED F11ACP 06.02 113414 GEN 149. 00014400 LB0:-00042030 ERRLOG 05.01 113054 GEN 148. 00055200 LB0:-00172013 PMT... 2.01 112414 GEN 148. 00007100 LB0:-00170121 COT... 2.02 111550 GEN 145. 00013500 LB0:-00175577 HRC... 03.01 111154 GEN 140. 00057400 LB0:-00172302 PMD... 07.03 110704 GEN 140. 00017600 LB0:-00200220 SYSLOG 04.00 112020 GEN 130. 00020400 LB0:-00200502 SHF... 07.00 116664 SYSPAR 105. 00003200 LB0:-00172601 FIXED RCT... 5.00 112144 GEN 100. 00011500 LB0:-00172565 FXR... 03.01 111300 GEN 100. 00003300 LB0:-00172214 BAP0 04.11 113200 GEN 80. 00047600 LB0:-00045441 QMG... 03.05 112270 GEN 75. 00034500 LB0:-00200250 LP0 06.00 112634 GEN 70. 00016700 LB0:-00177663 ACNT 06.02 111674 GEN 50. 00052400 LB0:-00175150 SHUTUP 04.02 110434 GEN 50. 00015400 LB0:-00173050 ...RMD 4.03 002027+ GEN 225. 00041100 LB0:-00174444 ...DCL 4.02 002003+ GEN 160. 00056100 LB0:-00171066 ...DMO 04.01 002005+ GEN 160. 00017300 LB0:-00170713 ...MCR 04.09 002021+ GEN 160. 00040300 LB0:-00173071 ...MOU 26.05 002023+ GEN 160. 00045300 LB0:-00172674 ...CA. 14.01 002057+ GEN 150. 00025000 LB0:-00173700 ...INS 15.00 002017+ GEN 100. 00051200 LB0:-00172456 ...SAV 09.00 002053+ GEN 100. 00061000 LB0:-00166674 ...UFD 7.00 002061+ GEN 100. 00014300 LB0:-00174072 ...ACS 3.01 002035+ GEN 70. 00004100 LB0:-00175541 ...ACC 04.00 001775+ GEN 65. 00031300 LB0:-00175060 ...SHA 05.01 002055+ GEN 65. 00030500 LB0:-00174766 ...AT. 9.0 002011+ GEN 64. 00052000 LB0:-00177277 ...INI 23.02 002013+ GEN 60. 00036000 LB0:-00172364 ...HOM 23.02 002015+ GEN 60. 00036000 LB0:-00172364 ...BRO 07.00 001777+ GEN 50. 00036400 LB0:-00170017 ...BYE 05.00 002001+ GEN 50. 00020400 LB0:-00170142 ...HEL 04.02 002007+ GEN 50. 00033600 LB0:-00176422 ...PIP 17.06 002025+ GEN 50. 00027200 LB0:-00200137 ...UNL 5.02 002031+ GEN 50. 00021000 LB0:-00200525 ...ACD 2.00 002033+ GEN 50. 00041200 LB0:-00167602 ...BOO 02.00 002037+ GEN 50. 00033400 LB0:-00167761 ...CON 03.00 002041+ GEN 50. 00130200 LB0:-00170416 ...ELI 04.01 002043+ GEN 50. 00031700 LB0:-00176366 ...LOA 5.02 002045+ GEN 50. 00037200 LB0:-00172613 ...MAG 03.00 002047+ GEN 50. 00036400 LB0:-00170060 ...PSW 03.00 002051+ GEN 50. 00015700 LB0:-00055203 YLA OFL CPA CSR=177560 VEC=60 PRI=5 YVA OFL CPA CSR=160440 VEC=300 PRI=5 DUA OFL CPA CSR=172150 VEC=154 PRI=5 DUB OFL CPA CSR=160334 VEC=354 PRI=5 MUA OFL CPA CSR=174500 VEC=260 PRI=5 LPA OFL CPA CSR=177514 VEC=200 PRI=4 CO0: OFL DRIVER TT0: YLA0: OFL DRIVER TT1: YVA0: OFL DRIVER TT2: YVA1: OFL DRIVER TT3: YVA2: OFL DRIVER TT4: YVA3: OFL DRIVER TT5: YVA4: OFL DRIVER TT6: YVA5: OFL DRIVER TT7: YVA6: OFL DRIVER TT10: YVA7: OFL DRIVER TT11: YVA10: OFL DRIVER TT12: YVA11: OFL DRIVER TT13: YVA12: OFL DRIVER TT14: YVA13: OFL DRIVER TT15: YVA14: OFL DRIVER TT16: YVA15: OFL DRIVER TT17: YVA16: OFL DRIVER TT20: YVA17: OFL DRIVER VT0: OFL DRIVER RD0: ONL DRIVER DU0: DUA0: OFL DRIVER DU1: DUA1: OFL DRIVER DU2: DUA2: OFL DRIVER DU3: DUA3: OFL DRIVER DU4: DUB0: OFL DRIVER DU5: DUB1: OFL DRIVER DU6: DUB2: OFL DRIVER DU7: DUB3: OFL DRIVER MU0: MUA0: OFL DRIVER LP0: LPA0: OFL DRIVER NL0: OFL DRIVER POOL=1200:13138.:13138.:1771 >; >; When you are finished with SYSGEN, software boot in your target >; system. Set the date and time, and save the system without any >; switches to verify that the system is working. Then save the >; system again, this time with the /WB switch to make it hardware >; bootable. >; >; The optional SAVE switches are: >; >; /WB writes the boot block >; /SFILE="filename" uses "filename" as the startup file >; /MOU="mount-switches" specifies mount switches to be used >; when the system volume is mounted >; >; For example: >; >; >BOOT [1,54]RSX11M.SYS >; XDT: 24 >; >; XDT>G >; RSX-11M-PLUS V3.0 BL24 >; >; > >; TIM 19-APR-85 12:00:00 >; >SAV >; >; RSX-11M-PLUS V3.0 BL24 256.K System:"MJTOAD" >; >RED DB:=SY: >; >RED DB:=LB: >; >RED DB:=SP: >; >MOU DB:"RSX11MPBL24" >; >@DB:[1,2]STARTUP >; . >; . >; . >; >* Please enter time and date (HH:MM MM/DD/YY) [S]: ^Z >; >@ >; >SAV /WB >; >; RSX-11M-PLUS V3.0 BL24 256.K System:"MJTOAD" >; >RED DB:=SY: >; >RED DB:=LB: >; >RED DB:=SP: >; >MOU DB:"RSX11MPBL24" >; >@DB:[1,2]STARTUP >; . >; . >; . >; >* Please enter time and date (HH:MM MM/DD/YY) [S]: 12:01 4/19/85 >; >TIME 12:01 4/19/85 >; >ACS SY:/BLKS=1024. >; >CON ONLINE ALL >; . >; . >; . >; >@ >; >SET /UIC=[1,54] >; >PIP [2,54]*.*;*/DE >; > >; >; You may wish to edit [1,2]STARTUP.CMD and [1,2]QMGSTART.CMD >; to reflect your desired initialization operations. >; >SET /UIC=[200,200] >; >REM MACT0 >REM PIPT0 >REM LBRT0 >REM TKBT0 >REM VMRT0 >; >; End of SYSGEN >; >TIME 00:35:52 13-AUG-04 >; >ASN = >; >@ >